Mad Professor Ruby Red Booster pedál

Mad Professor Ruby Red Booster pedál

A Ruby Red Booster a BJF Little Red Trebler és Red Rooster Booster pedálok alapján épül fel, ez a két booster elektronika van ebben a sorrendben egymásután kötve egy master hangerő szabályzóval. Használható mint Treble (magastartomány) booster, clean (tiszta) booster vagy mint egy Overdrive fokozati meghajtó bármelyik kombinációban. Használható buffer áramkörrel vagy anélkül is. A Treble (magastartomány) booster finoman hangolt és csak a megfelelő magastartományokba nyúl bele és optimalízáltan vágja a mély hangtartományt. A Booster áramköre úgy lett tervezve, hogy az enyhétől az egészen erős Overdrive fokozatig meghajtsa az erősítő bemenetét, a Boost 40dB emelésre képes. Ez a Booster magasabb beállításban saját zenei torzítást ad a hangzásnak. A kétféle Booster teljes jelszintje szabályozható a Master hangerőszabályzóval és a torzítás mértéke is ezzel a szabályzóval állítható.
55 000 FtIncludes 27% VAT
Nem rendelhető
Jelenleg nem rendelhető
    Részletes leírás

    INGYENES KISZÁLLÍTÁS

    Ruby Red Booster pedál Mad Professor

    Controls

    MASTER: this is a volume control that is located directly after the booster circuit and when set to max it is just a resistor to ground. This control sets the final output and it can be used to control the output when the pedal is used for overdrive (Boost turned up).
    TREBLE: set treble boost from zero to about 15dB. The treble frequency and bandwidth are carefully tuned with an optimized bass slope.
    BOOST: the gain of the booster and can be set from unity to about 40dB of boost. When this control is cranked the unit will distort within itself.
    BUFFER: inside the pedal there is a switch for a high quality buffer. You can set the pedal for true bypass mode or “buffer on” in bypass mode. We recommend using a buffer in your signal chain to help with the treble and gain loss from using many pedals and/or long cables. Pedals are shipped “buffer on”.The Mad Professor RRB Buffer is an amplifier with a voltage gain of exactly 1x (times). The RRB buffer output impedance is set a little lower than the Dc resistance of a standard guitar pickup to equalize the effect of following load impedance. Input impedance is set at 500K for a medium load to standard guitar pickups. This keeps the tone and guitar volume taper natural.

     

    Settings
    TREBLE BOOST: Set Boost to minimum and Master to maximum and adjust for desired treble boost with the Treble knob.
    STRAIGHT BOOST:Set Treble to minimum and Master to maximum and adjust Boost to desired effect.
    BOOST: the gain of the booster and can be set from unity to about 40dB of boost. When this control is cranked the unit will distort within itself.
    DISTORTION: Set Boost to maximum and adjust output level with Master to unity, then adjust Boost for desired depth and overdrive. Treble can be used to enhance distortion effect.

    CAUTION !
    Never operate the unit with its bottom removed or damage will most likely occur.

    Electrical specifications
    Input impedance: approximately 500K Ohm’s
    Recommended output load: 50K Ohm’s or higher, effects output and buffer output
    Current consumption @ 9V DC: approximately 6mA
    DC supply voltage range: 8-18V
    Voltage gain: approximately +40dB
    Treble boost: peak +15dB@4KHz
    Signal to noise ratio: 110 dB
    Effect 3dB bandwidth: 70Hz to 7KHz
    True bypass or buffered (switchable inside the pedal)

    POWER REQUIREMENTS: 6F22 9V battery or DC eliminator 2.1 mm plug center negative and positive sleeve.

    NOTES: RRB is protected against wrong DC eliminator polarity. Fuzzy sound is a sign of low voltage. Maintain recommended voltage for best results.

     

    Manufacturer
    Effekt típus
    Booster
    SKU
    MP-RUBYRED

    Kiválasztott termékek

      Összehasonlítás

      Iratkozz fel hírlevelünkre!

      The subscriber's email address.
      Feliratkozásod
      Select the newsletter(s) to which you want to subscribe.